If you have your Z-Axis set up and the calibration step went well, you shouldn’t have any problems cutting the final sled. I ended up getting a prototype of the new MakerMade sled in the mail, so I used that, and it was so nice to have it all ready to go. I just had to add a few holes for the bolts that hold the router into place. The sled doesn’t come with those holes pre-drilled because not everyone uses the same router. I had kind of improvised with my temporary sled, I’d used a tabletop round, and gone with a smaller size than recommended because I liked the idea of a more compact sled. I’d also put my weights in a different position. Once I got this sled set up, though, I realized that some of the problems I’d been having up to that point were because of my sled. Everything moved so much more smoothly once I had a perfectly balanced sled, and I think the larger size helped stabilize movement, too. In the Maslow forum, you’ll see that people use all kinds of things for weights. You might think that anything goes, and that’s true, to

MAKING ALL THE MISTAKES SO YOU DON’T HAVE TO Up until the point of calibration, I had a few misadventures but mostly things went pretty smoothly. This is where it got bumpier. In the online assembly instructions on the Maslow forum, Step 6 was “attach sled to frame” and Step 7 was “calibrate”. So I started the calibration process with my sled attached to the frame. As I extended the chain across the frame to measure the distance between motors, the position of my sled became more and more precarious until it was hanging in the air. This seemed clearly wrong, but I couldn’t find anything specifically saying to remove the sled from the chains. It wasn’t until a few steps later that it became clear I’d need to not only detach the sled, but basically dis-assemble the whole chain/ pulley/ elastic cord setup that I’d just assembled, and then a few steps later redo it all. I’m not given to foul language, but I HATE re-doing something I just did. I’m all about the adventure of learning new things, but the second time around it’s not an adventure anymore, it’s just drudgery. I found it really difficult to detach

MAKING ALL THE MISTAKES SO YOU DON’T HAVE TO Adding the Z Axis had its challenges, and reliable Z Axis operation continues to be an issue for many Maslow users. While I was in the thick of setting it up, it felt like I’d never get it to work, but after working through a lot of what turned out to be user errors, and a few bugs in design, I have it working pretty reliably. Maker Made is prototyping a Z Axis solution that will cut through the remaining issues and make it rock solid. I’m super excited to try that out when it’s ready! The most important thing to know about the Z Axis is that you don’t want to Maslow without it. When I first calibrated my machine and tried to cut out the final sled, I was following an online assembly guide that has you add the Z Axis AFTER calibration and cutting the final sled. So I tried to cut the final sled without a Z Axis. Meaning that every time there was a change in bit depth, I had to: pause the cut walk from my computer to my frame setup turn the router off

I’ve never used a router, so this part was a bit of a challenge. I didn’t know how to add the bit, for one thing, and there were a surprising dearth of Youtube videos showing how to do it, at least for this particular router. I watched a lot of reviews of the Ridgid router, and some of them showed a little bit of how to use it, but there were still a lot of gaps. After a couple of hours of watching videos, and in general putting it off, I decided I just needed to plunge in and do it. I figured out how to put a bit in, clamped my wood to the work bench- with blocks underneath so I didn’t accidentally route a hole in the work surface, donned some safety goggles and flipped the “on” switch. I was surprised and fascinated by how smoothly the router carved away the wood, and how relatively easy it was to control. My finished product was a bit wobbly looking, but I was disproportionately proud of it. Usually for the temporary sled you only need to carve a hole in the middle, but the wood round I bought so I

I was a little apprehensive about setting up the electronics for the Maslow. I’ve been an occasional reader of Make magazine, I’d heard the term Arduino, but I’d never seen one in person. I like to make things, but that’s mostly been rough woodworking, fiber related, or graphic design- nothing with electronics or chips of any sort. But the Maslow designers really made the process easy. I sat down at my kitchen table, laid out all the parts, and was done in about half an hour. I had a few hiccups, like not realizing I was supposed to open a program once I’d downloaded it, so I tried to make sure the instructions I wrote for the manual spell out details like that. Tools Needed Power Drill Screwdrivers Safety goggles Computer or tablet Internet connection Materials List Part #1 AC Power Cable Part #2 Arduino with Heat Shield Part #4 DC Power Supply Part #9 USB Cable Part #10 Flash Drive (optional) Part #11 X and Y Motor Cables Part #12 X and Y Motor Mounts Part #13 X and Y Motors Hardware Bag #5 Hardware Bag #6 STEP 1: CONNECT THE MOTORS X and Y motor cables, as well